复杂形态钢结构设计培训班

首页 朱明之关于建筑-公众号 轻钢笔记《轻骨架建筑如何选用纤维水泥楼板基板》

轻钢笔记《轻骨架建筑如何选用纤维水泥楼板基板》

INEX>FLOOR is a high strength lightweight flooring substrate with tongue and groove (T&G) edges. It can be used for external or internal applications; as a substrate for most finishes such as tiles, vinyl, carpet or timber.

INEX>FLOOR can be used in conjunction with floor systems to achieve up to BAL-FZ bushfire compliance.

INEX>FLOOR is simplicity itself. A single affordable product for multiple flooring applications.


WEIGHT

At either approx. 40kg (19mm) or 34kg (16mm) INEX>FLOOR is lighter weight and easy to handle on site.

STORAGE

INEX>FLOOR should be stored dry, flat and with all edges protected from damage. We recommend storage undercover and raised from the ground.

HANDLING

Wear protective gloves when handling or cutting sheets


FRAMING

INEX>FLOOR can be fixed to timber or steel joists at a maximum of 600mm centres*. Refer to page 7 for loading properties.

Timber framing must be in accordance with AS 1684 – ‘Residential timber-framed construction’.

Steel framing must be in accordance with AS 3623 – ‘Domestic metal framing’.

Ends or edges without the tongue and groove (butt ends) must be supported by a joist.

Ensure framing is level prior to fitting


ASSEMBLY

INEX>FLOOR can be fitted to a square or staggered layout, but must be staggered for tiled or vinyl finishes. Where waterproofing is required:

• Lay rough side up.

• Ensure butt joints are over timber/metal joists and have a 2mm gap and are filled with INEX>BOND.

• Ensure all T & G joints are filled with INEX>BOND.

FIXINGS:

Ensure all fixings are located:

• 20mm min. from all tongue and grooves;12mm min. from all butt joints

• 50mm min. from all corners

• Max. 200mm centres along joists.

• Run a 6mm bead of INEX>BOND on top of the timber or steel joists below each sheet progressively as they are fixed in place.

Ensure framing and INEX>FLOOR boards are clean and dry prior to fitting.

FIXINGS – TIMBER JOISTS – Class 3 Galvanised Fixings or higher*

Screws: 10gx50mm self-embedding countersunk head screws.

FIXINGS – STEEL JOISTS – Class 3 Galvanised Fixings or higher* 

Screws: 10gx40mm self-drilling, self-embedding, countersunk head screws.

*Class 4 or Stainless Steel screws for sea spray zone in accordance with AS3566


FINISHES

CLEAR: For specifiers wishing to retain INEX>FLOOR’s raw concrete like

appearance*, refer to the COATINGS menu on UBIQ’s website.

*Interior application only.

WET AREAS/TILES: Install INEX>FLOOR rough side up. For wet areas

such as showers a waterproof membrane is required in accordance with

the Building Code of Australia.

CARPET, VINYL or TIMBER: Install INEX>FLOOR with the smooth side up.

GENERAL: Ensure all components and adhesives are compatible with

each other.








本文来自网络,不代表钢构人的立场,转载请注明出处。搜索工程类文章,就用钢构人网站。 https://www.ganggouren.com/2021/01/4d0ec897de/

钢结构地图

上一篇
下一篇

作者: ganggouren

为您推荐

发表回复

您的电子邮箱地址不会被公开。 必填项已用 * 标注

联系我们

联系我们

17717621528

在线咨询: QQ交谈

邮箱: 1356745727@qq.com

工作时间:周一至周五,9:00-17:30,节假日休息
关注微信
微信扫一扫关注我们

微信扫一扫关注我们

关注微博
返回顶部